博九彩票

National Hotline:0757-29899345
Support
Current Location:Home > Support
Laser marking machine operating procedures and maintenance
Add Time:2018-10-08
Laser marking machine is also called laser engraving machine, laser engraving machine, laser inkjet printer, laser marking machine, laser marking machine, laser deep engraving machine, laser machine, laser machine, etc., and the localities are different. It is a relatively common industrial manufacturing equipment. Foshan Fulan Laser Technology Co., Ltd., in order to better use laser marking equipment for customers, specially prepared an easy-to-understand laser marking machine operating procedures and maintenance for everyone to read!

                                  
First, the laser marking machine operating procedures:
 
     Before starting the machine: Please clean the work surface before starting the machine, check whether the laser marking machine is safely grounded, check the power cord of the marking machine, and make the connection correct and reliable.

1, boot steps:
1. Turn on the laser marking machine power supply (after the power is turned on, the working indicator light is always on and the fan is running);
2. Insert the key switch and turn 90 clockwise to the "on" position;
3 Turn on the industrial control switch, the industrial control computer starts automatically, and the laser marking software is turned on;
4 Make sure that the emergency stop switch is not turned on (ie, the switch is bounced up and is in an automatic closed state);
5 Turn on the key switch, turn on the laser switch, and the laser system starts automatically;
6. Remove the laser galvanometer protective cover.

2, marking operation:
1. Open the marking software;

2. Select the marking file → Open → select the file to be marked (or the new graphic to be marked by the editor);



3. Alignment: Click “Red Light” below the mouse, and the laser head will release the red square to shoot on the marking part. Shift the workpiece so that the box falls on the part to be marked. After adjusting, click “Stop Red”, then Fix the tooling.
4. Focusing: Place the workpiece sample on the part to be marked (use the unqualified or substitute parts of the contour to avoid bad marking and waste), use the low frequency as much as possible, then check the continuous marking and click the mouse. Continuous processing", then click "marking", shake the Y-axis up and down until the laser is applied to the workpiece, the energy is the strongest, the sound is the most crisp, and the color is the brightest, it is basically the focal length, and it has been tested several times. , find the right focal length. (Foshan Fulan Laser Xiaobian hereby reminds you: "Continuous processing" is used when focusing. After adjusting the focal length, please remember to turn "continuous processing" off and then operate.)
PS: Manual focusing head is a very troublesome thing, because manual focusing is used, the speed is slow, the efficiency is low, and the focusing accuracy is not guaranteed, so that many waste products are produced. For this reason, Foshan Fulan Laser Technology According to the needs of the market, the company has independently developed a system ------ automatic focusing system. Auto focus system, can be configured in any laser marking equipment. It is only necessary to install a visual positioning system on the original laser equipment, and realize the automatic focusing and marking by the visual positioning system, and the automatic focusing can be realized even if the thickness of the workpiece is slightly different.
5. After the test is completed, the marking work can be carried out. (To mark multiple workpieces, just repeat this step).

3. Shutdown steps:
1 After confirming that the IPC is not running any software, turn off the key switch, turn off the laser switch, and the laser system will automatically turn off;
2 Turn off the laser marking software;
3 Turn off the industrial computer in the computer system;
4 Turn off the main power switch.
5, remove the key, have someone to keep it, in case of next use;
6. Cover the lens cap.
     
Second, the maintenance of laser marking machine:
1. Keep the workplace and equipment clean.
2. Open the chassis of the marking main control computer every year to clean the internal dust.
3. When moving the laser marking machine, be careful not to strain the laser transmission tube.
4, the laser up and down moving components, half a year to check the lubrication situation.
5, do not casually install software that is not related to work, clean up the internal files of the computer once every six months.
6, to strictly follow the startup steps of the equipment to operate, do not operate indiscriminately.
7. Never open any end caps while the equipment is in operation.
8. The laser and optical lens are fragile. Handle with care and avoid vibration.
9, using water-cooled, cooling water must be pure, non-sticky, often replaced, it is best to use distilled water;

10. If there is any abnormality during the operation, the equipment should be shut down imtely, and the personnel should be arranged to check and maintain the equipment. Please note: To be repaired by a professional or authorized supplier of the equipment supplier, do not disassemble it yourself.





友情链接:天天彩票  传奇彩票网  M5彩票官网  皇冠彩票  皇冠彩票官网  M5彩票平台  皇冠彩票  

免责声明: 本站资料及图片来源互联网文章,本网不承担任何由内容信息所引起的争议和法律责任。所有作品版权归原创作者所有,与本站立场无关,如用户分享不慎侵犯了您的权益,请联系我们告知,我们将做删除处理!